NewBlot™ PVDF Stripping Buffer for PVDF Membranes (100 ml)

166,40

NewBlot PVDF stripping buffer is specially formulated for IRDye®secondary antibodies including IRDye 800CW, IRDye 680RD, and IRDye 680LT. This stripping buffer is not compatible with IRDye 700DX secondary antibodies.

NewBlot PVDF is intended for PVDF membranes only and is ideal for removal of secondary antibody.

Saadaval järeltellimisel

Tootekood: 928-40032 Kategooriad: ,

Specifications

NewBlot PVDF Stripping Buffer is supplied as 5X concentrated solutions. Each 100 mL bottle is sufficient for up to 3000 cm2 or approximately fifty 7 x 8.5 cm Millipore® Immobilon®-FL PVDF membranes.

NewBlot PVDF stripping buffer contains hazardous materials and additional shipping costs will be applied.

Example Data

Example of stripping and reprobing with NewBlot PVDF Stripping Buffer.
Figure 1. Example of stripping and reprobing with NewBlot PVDF Stripping Buffer. (A) Invitrogen EPAGE-96 6% gel loaded with replicate A431 lysate samples and detected with anti-Syk (IRDye 680, red bands) and anti-β-Tubulin (IRDye 800CW, green bands). (B) Stripped with NewBlot-PVDF Stripping Buffer for 5 min at room temperature. (C) Blot was reprobed with anti-Syk and anti-β-tubulin antibodies. All blots have been scanned at 169 µm resolution and scan intensity of 6 on the Odyssey Classic Imager.
Incubation time, buffer concentration, and temperature affect stripping efficiency
Figure 2. Images showing an example of Western blot stripping optimization with NewBlot PVDF Stripping Buffer. (A) Initial Western blot, showing EGFR detected with IRDye 800CW goat anti-mouse and β−Actin detected with IRDye 680LT goat anti-rabbit. (B) After stripping with standard stripping Procedure. (C) After stripping for an additional 20 min. (D) After additional 5 min stripping with the addition of SDS. (E) After 20 minutes total stripping time in NewBlot PVDF + SDS. (F) Reprobe image showing ERK2 detected with IRDye 680LT goat anti-mouse and β−Tubulin detected with IRDye 800CW goat anti-rabbit.

Factors Affecting Efficiency when Using NewBlot PVDF Stripping Buffer

Recommended standard conditions: 1X NewBlot PVDF for 20 min at room temperature.

Below are factors that affect stripping efficiency with NewBlot PVDF on PVDF membranes. Figure 2 above shows the effects of incubation time and addition of SDS on stripping efficiency. These blots and protein targets were not sufficiently stripped using the standard Procedure, and optimization was performed.

For optimal stripping results, follow the optimization guidelines in NewBlot PVDF Stripping Buffer pack insert.

Amount of time blot is in stripping buffer

Stripping time has the greatest effect on efficiency.

Increasing the stripping time may lead to increased damage/loss of target antigens, and reduce the success of reprobing.

Sample type and preparation

Even under the most stringent stripping conditions, the fluorescent signal may not be removed completely due to sample load amount, antibody affinity/avidity, and target protein abundance.

Blot handling conditions

Washing, scanning, or stripping efficiency will be affected if the blot is allowed to dry at all during incubation. Keep the blot moist at all times.

Detergent may help remove fluorescent signal

If fluorescent signal remains, try longer incubation times first, followed by addition of SDS.

Temperature used for stripping

If fluorescent signal remains after the above steps, incubation in stripping buffer may be carried out at 37 °C using a water bath or incubator.  This should only be attempted if the above optimization steps are unsuccessful.

Kaal 0,050 kg
Säilitamine

Toatemperatuuril

Maht

100 ml

Shopping Cart